How To Remove Frozen Toilet Tank Bolts

Use the screwdriver to hold the bolt in place. As a general rule you want to start with the least destructive method and work your way up.

Removing Rusty Toilet Tank Bolts Doityourself Com Community Forums

RYOBI AG4031G 4-12 Angle Grinder.

How to remove frozen toilet tank bolts. The typical toilet has a dome-shaped cap over each bolt both to. Cant remove frozen toilet flush handle. I dont want to use a hack saw so I have a black and Decker.

Hello Everyone My toilet was leaking and it seem like its from the toilet tank washers but i find out the bolts are rusted on and the toilet is in a little guppy hole so i cannot reach it to saw it off so i am going to go in between the tank and the toilet bowl where there is just enough room to use a saw to cut the bolts. Tips for Removing Stuck Toilet Bolts. Remove the plastic cap over the stuck bolt if you havent already.

In this Toilet Tank Bolts Leaking video Bob explains the methods of cutting off the bolts that hold the toilet tank onto the toilet bowl. You will need to clean up the area where the old bolt head was or you may develop another leak if the new washer doesnt sit right. Httpsamznto2BNYYjrSani Seal Green Waxless Toilet Gasket.

The regular process means that way you used to follow to remove bolts from somewhere. Jump to Latest Follow. Sometimes the bolts are corroded and will not just come off.

How to Remove Toilet Tank Bolts. Remove the Nuts Try turning the nut on the anchor bolts counterclockwise with a wrench. Insert a screwdriver through the hole in the bowl of the toilet and push the bolt to the side.

I wasnt able to loosen it at all. Ive cut many screws and bolts this way. Take off the tank and put it on the ground for safety.

Okay I thought replacing the flush handle would be a 5 minute job but when I pulled off the tank lid I found that the nut and bolt threads on the inside of the tank were encrusted with what Im assuming is limescale see pic. The first step to remove your toilet tank bolts rusted or not is to take a flat head screwdriver and a wrench. Use a wrench to remove the nuts from the bolts after loosening the nuts.

Removing any of these can be a challenge do to rust and corrosion. Toilets have 3 pairs of bolts. Remove the Tank Bolts.

Try a hacksaw and cut through the bolt. It also covers a few ways to avoid stuck and rusty bolts. Cut through the stuck bolt and the toilet will come right up.

Remove the toilet lid leaving the tank totally open. Use the flathead screwdriver to hold the bolt in place and then seat the wrench over the nut on the underside of the tank and turn wrench counterclockwise to loosen. Pull the nuts out once theyre loose.

Kung Fu Maintenance demonstrates the reciprocating saw method for how to remove a frozen stuck tank to bowl toilet bolt by cutting it in half. For this you need a flathead screwdriver and a good wrench that you can adjust. Two connecting the toilet seat two connecting the tank to the bowel and two holding the toilet to the floor.

If you cant cut the bolt you may be able to cut the nut in the direction of the bolts axis then pry the nut apart at the cut line. I would try a Dremel type tool with an abrasive cutoff wheel. Lift off the Tank.

If the toilet tank bolts are not too rusted you may follow the regular process to remove the bolts. Of course you need to be careful of the porcelain. You may use a screwdriver to turn the bolts.

If you have experi. This will allow you to pull the tank off of the bowl but you will be left with the stubs of the bolts sticking out. Tools used in this video.

Tap lightly on the stub and push the bolt head out. If you find that the bolts are swiveling use the wrench to back the nut off while you unscrew the bolt with a long screwdriver from inside the tank. Unscrew nuts from bolts In order to remove the toilet tank bolts you will need a flat head screwdriver and a wrench.

How to Remove Toilet Tank Bolts Now use your wrench to loosen the tank bolt nuts from underneath the toilet bowl. Rubber washers removal and. Then take the wrench over the nut under the tank and turn it counterclockwise.

Now place the flathead screwdriver in the bolt to hold it in the position. This will loosen it. This video shows a few ways to remove rusty corroded stuck toilet tank to bowl bolts.

How To Remove Rusted Toilet Bowl Tank Bolts Youtube