How To Remove Mold From Wood Gun Stock

They have probably grown down into the wood as well as out onto the surface. Soap and Water If you just want to get some dirt and dust off of the synthetic stock regular soap and water will do the trick.

Refinishing A Gun Stock 7 Steps Instructables

Now you are going to have to remove the butt plate or recoil pad and with a cloth dampen it and dab a little on the face of the butt.

How to remove mold from wood gun stock. Bore cleaning and stock removal next. Allow the first layer to settle for a few minutes. Then rinse with clear water and dry.

Pour an even layer of fiberglass and resin over the stock and clay. Even if it does not kill any type of mold it is a cheap natural solution that you can apply on any surface and material. Take the barreled actions out of the stocks and clean the metal and wood separately so you can get inside them and avoid getting any bleach on the metal.

Meaning the mold most likely is not just on the surface but now into the wood. Make a solution of 8 to 10 tablespoons of washing soda and 1 gallon water. Let it dry and hosed it down with ballistol.

Dehumidify and air it out till it is bone dry assume you fixed the heater and get rid of all wood that is in subfloor that is saturated. Bleach everything except gun stocks that has mold. Test the solution in an inconspicuous spot like inside the barrel channel first to be sure it wont harm the finish and then gently wash the stocks with the light bleach solution and let them dry out as much as possible.

Remove all the metal parts off the stocks. Home Cheapo now carries products that do that. For a small amount of mold growth that has not left severe stains or penetrated the wood distilled white vinegar can kill the spores.

My recommendation is get some weed killer and make a small sample up such as a table spoon of weed killer and a table spoon of water. Add two more layers. Some minor rust on sling swivels and trigger guards but look to be in great shape.

If you have a way to pressure Clorox into the wood you might get rid of it you might not. You could clean the wood with bleach but since wood is porous the old spores will not be killed. You might try stripping the stocks off the guns and using something like Murphys Oil Soap to clean.

If you dont shoot them much coat them with petroleum jelly. Allow the vinegar to remain and air-dry on the surface for at least one hour. Prepare a solution of three parts Murphys Oil Soap to one part water.

Use a spray bottle to lightly mist the wood with the vinegar. Clean the stocks with mild detergent and water. Your going to have to kill the mold.

Once the guns are dry oil them down. I tried the 5050 vinegar wipe down outdoors let sit and rinse liberally with wet rag. Allow the mold to dry for 24 hours.

I would tear them down. Scrub the mildewed surface using a soft-bristled brush. About one cup is all that is needed to clean the stocks on several guns.

I did this on my MkI Ross restoration elsewhere on this site. This solution can be used on most painted or stained wood surfaces. Mold is dangerousand hard on respiration.

The other option is to completely seal the wood so air cant get to the spores. One of the most popular solutions to remove mold from wood is white vinegar. Mildew isnt a real problem here so.

Another option is to let the wood sit in a 55 degree Celsius convection oven for about for 15-30 minutes depending on the stocks. Bleach does not kill mold in porous materials like wood. Use a toothbrush or some other soft bristle brush for the tough spots.

You can rub it with any type of soap you want such as Dial. Clean all the metal with gun oil. With white vinegar in a spray bottle spray down the insides of the safe allow to dry then vacuum.

They look great and I can handle them now without coughingsneezing and watery eyes. The simplest solution you can make contains half water and half vinegar. Just rub it with some soap and wipe clean with water.

Interior Wood Surfaces. Mold spores are in the pores of the wood. If it is just on the surface you can preserve the original finish by dry rubbing the mold off with 0000 steel wool.

Shouldnt damage finishes since its made for furniture. Dip a clean cloth in the solution until it is damp not sopping and wipe down the length of the stock the grip and any other wooden parts on the gun. You need a solutionproduct that kills mold spores.

50 waterHydrogen peroxide kills mold and mildew also.

Pin On My Guns