How To Solder A Toilet Shut Off Valve

I noticed that some of the solder had formed as a drip at the bottom of the pipe. Disassemble the Shutoff Valve.

Need To Replace Toilet Water Shut Off Valve On Cpvc Pipe Doityourself Com Community Forums

The first is old-school soldered in place.

How to solder a toilet shut off valve. The leaking valve is soldered on and I bought the same kind except the new one is a 14 turn valve. Leah from See Jane Drill demonstrates how to remove an old water shut-off valve for a toilet and install a new one compression type. Water supply valve is almost dead center with toiletflange making installation of new toilet difficult if not impossible.

The one in your first post that shows the older valve is the same one a plumber installed replacing the plastic valve shut off I had. Use a wrench or plier for loosening the nut at the other end of the valve connected to the water supply line. Place a bucket under the old valve.

Water Shut-off valves also called supply stop valves allow people to connect supply lines to sinks and toilets. If removing a solder-type valve cut the supply line with a pipe cutter. Disassemble the shutoff valveleaving the toilet and supply lines intact.

Next remove the old compression sleeve and nut. I believe I can get away with running pipe OUTSIDE of the wall eg. Valve is connected to.

Avoid gumming up the inside of the shutoff valve. He saw what I had and did a replacement without charging me. The goal is to cool things down quickly.

Use a dry cloth to wipe the piping. Clean the washers with a cloth. They also help isolate and repair leaks nea.

Determining if your water shut off valve is a solder or compression union will not involve a complicated home-improvement algorithm but rather one simple step. One day the toilet continued to run even though everything inside looked okay. So I shut of the main valve to the house and left.

Drape the frame with a protection cloth and secure it to the wall. Grabbed the bottle of spray water and spritzed both the valve still in the wrench and the pipe in the wall. Learn how easy it is.

I tried to shutoff the water at the toilet before I left the house but it wouldnt turn off all the way. Using the existing pipe that sticks out of the wall remove current valve then attach some elbowbend to it. Assuming they are solder on you must heat them to melt the solder and remove them or cut them free with a tubing cutter as close to the existing valve as possible.

You need to tighten the inlet of the toilet line in the shutoff valve. If you unsolder them take great care to remove all the old solder and cleansmooth the pipe end well before attempting to solder a new valve. Terry who sells these types of toilet valves you show if I might ask.

Open the faucet to drain the line. Use a leather glove and a damp rag to hold on and pull it out. Flex the neoprene to try to get it supple again.

I need to replace it and purchased a new one. Make sure to shut off the main water supply before doing this repairDo it yourself replacement of a faulty shut off valve to a toilet. Use the rag to wipe away excess solder.

Two types of valves exist. Yesterday I turned the water off to the toilet while cleaning the bowl and when I finished up and turned the water back on the shut off valve started leaking pretty bad. Grab the compression nut with another wrench and turn it clockwise to loosen it.

I heated up the solder and took and old screw driver and scraped off the liquid solder. Previous to compression piping systems around the 1980s plumbers ran copper tubing that required a torch and solder. Dont use any pipe dope or plastic tape on the valve.

Get a soldering torch adjust it to its smallest flame and melt the solder until you can pull the valve out. One toilet needs replacing. Removal methods vary according to valve type.

Start by disconnecting the water line from the valve. I need to move the water supply valve. Then pull the valve off the copper tubing.

I did get the toilet shutoff to work by using WD-40 and turning the valve. Just bought a new house. To remove a compression-style valve hold the valve body with an adjustable or open-end wrench or a slip-joint pliers.

The plumber was here to cap my bathroom sink lines charging me 219.

How Do I Get These Toilet Shut Off Valve Out Home Improvement Stack Exchange